GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Allen Bradley - Drives |
Product Type: | Drive |
Part Number: | 2085-ECR |
Series: | 2085 |
Description:
The 2085-ECR was introduced by Allen-Bradley. This device provides high performance at a small size less expensive package. A variety of digital and analog modules are also compatible to expand the capabilities of the controllers by increasing the flexibility of input and output count and type. Few of the modules which are solid states can be easily availed in the market these could be recommended for the purpose of reducing the noise effects and the uses which are required for various switching waves, rather than transmission. Triac output is available on AC upload.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The 2085-ECR device controls are suitable for applications that require digital as well Analog I/O or high-performance analog I/O. The controls are the best for multiple inputs and outputs which are supported by four (4) of the extensions. This is available for twenty-four (24) and also forty-eight (48) digits in the board of Ethernet. These resources are the tools and gadgets needed for the high performance of a logical control system. The 2085-ECR serves as an end cap and is used to terminate the end of the serial communication bus. This device has the facilities such as interfacing, the tapes for the communication, and a few connectors. The 2085-ECR has additional input and output pins for both analog and digital systems. It also has different blocks which makes the installation process much easier.
The type of PLC you use will determine which accessories are needed. The programmable logic controls (PLCs) in the US command list, task block diagram, layout text, and sequence worksheets are useful programming languages and may be more relevant than stairs, depending on the application. The ladder circuit has new logic to make the circuit or cut off the coils. A single coil corresponds to each bit state in the configuration control memory. Each step of the ladder language usually has one (1) coil on the far right. Few developers might permit many outputs for the coil in the rung. The Input / Output module firmly intersects the right side of the Micro850 and Micro870 controls, supporting both mounting options.
Question: Does Automation Stop offer repairs on the 2085-ECR?
Answer: Yes. We offer repairs for the 2085-ECR and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Allen Bradley - Drives and 2085-ECR?
Answer: If you buy the 2085-ECR through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the 2085-ECR online?
Answer: Yes. Automation Stop sells the 2085-ECR online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the 2085-ECR?
Answer: The 2085-ECR is made by Allen Bradley - Drives.
For additional information about 2085-ECR check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding 2085-ECR.
Revision Part # | Also Known As | Availability |
---|---|---|
2085-ECR/A | 2085-ECR Ser A, Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.