GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Allen Bradley - PLC |
Product Type: | PLC/Programmable Logic Controller |
Part Number: | 1763-NC01 |
Series: | 1763 |
UPC: | 10662074051639 |
Description:
The 1763-NC01 is an Allen Bradley's connecting cable categorized as an accessory part. It belongs to the 1736 Bulletin. It is a cable that provides an interface between MicroLogix 1100 Channel 0 (8-pin DIN) to RS-485 (6-pin Phoenix). In addition, this cable is 30 cm 11.8 inches in length and weighs 304 grams. The product dimension is 8 x 8 x 7 millimeters. The manufacturer has discontinued this connecting cable.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The 1763-NC01 is a connector cable (8-Pin Mini-DIN to 6-Pin Phoenix). This cable is used to interconnect MicroLogix 1100 controllers. Additionally, it has been classified for class one, two hazardous locations, and applications. In addition, it is also used for connecting the networking modules, adapters, and drives belonging to a wide range of product lines. The length of this connector cable is 30 cm (11.8 in.). As far as its configuration to the controllers and peripheral network devices are concerned, the users can utilize this cable A or later that comes with the 8 pins and is a type of mini-DIN to 6 pins DH485 connection cable or similar. On the contrary, the controllers support a network port for establishing the connection for sharing and storing the data. Additionally, these controllers that are compatible with this cable can store up to 8 KB of data (4 kilobytes user application, 4 kilobytes data). Furthermore, controllers also allow online editing and enable users to access, monitor, and program with the help of a communication channel and a port. Aside from the MLX 1100 controllers' compatibility with the NC01 connection cable, the cable's configuration to the peripherals must be consistent and adhere to the manufacturer's wiring specifications. Only qualified individuals should configure these modules and ensure the units' safety in this regard. The manufacturers have discontinued this cable, but the users can still replace their old modules with the new one since it is still a popular connector cable for its compatible series.
Question: Does Automation Stop offer repairs on the 1763-NC01?
Answer: Yes. We offer repairs for the 1763-NC01 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Allen Bradley - PLC and 1763-NC01?
Answer: If you buy the 1763-NC01 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the 1763-NC01 online?
Answer: Yes. Automation Stop sells the 1763-NC01 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the 1763-NC01?
Answer: The 1763-NC01 is made by Allen Bradley - PLC.
For additional information about 1763-NC01 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding 1763-NC01.
Revision Part # | Also Known As | Availability |
---|---|---|
1763-NC01/A | 1763-NC01 Ser A, Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.