GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Allen Bradley - PLC |
Product Type: | PLC/Programmable Logic Controller |
Part Number: | 1771-ID01 |
Series: | PLC 5 |
Description:
Part number 1771-ID01 is an isolated AC/DC input module produced by Allen-Bradley. This device has six inputs, as well as one green module active indicator and sixteen red status indicators. The nominal input voltage is 220 to 240 volts AC at a frequency of 47 to 63 hertz. The input voltage range is 184 volts AC to 276 volts AC, or 184 volts DC to 276 volts DC. The operating temperature range is 0 to 60 degrees Celsius.
Key Features:
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The 1771-ID01 is an isolated AC/DC input module that was produced by the company known as Allen-Bradley. This Allen-Bradley product is equipped with six (6) inputs, with one (1) green module active indicator and sixteen (16) red status indicators. The noinal input voltage of this device is 220 to 240 volts alternating current (AC), or 240 volts direct current (DC), at a frequency of 47 to 63 hertz (Hz). This device has multiple nominal input currents. These nominal input currents include three (3.0) milliamperes at 220 volts AC fifty (50) hertz, 3.5 milliamperes at 220 volts AC sixty (60) hertz, and three (3.0) milliamperes at 220 volts DC. Additionally, the input voltage range for this Allen-Bradley product is 184 volts AC to 276 volts AC, or 184 volts DC to 276 volts DC.
The Allen-Bradley 1771-ID01 has an on state current minimum of 1.8 milliamperes and an off state current maximum of 0.7 milliamperes on AC and 1.0 milliamperes on DC. The on state voltage minimum of this device is 184 volts AC, with the off state voltage maximum being 102.09 volts AC and 144.4 volts DC.The power dissipation rating of this product is 2.4 watts maximum and 0.4 watts minimum. The thermal dissipation rating of this device is 8.3 BTU/hr maximum and 1.4 BTU/hr minimum. This device's backplane current is seventy-four (74) milliamperes.
The temperature range for the Allen-Bradley 1771-ID01's operation should remain between 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit). The storage temperature range of this device, however, should remain between -40 to 85 degrees Celsius, or -40 to 185 degrees Fahrenheit. Additionally, the relative humidity should always be 5 to 95% non-condensing.
Question: Does Automation Stop offer repairs on the 1771-ID01?
Answer: Yes. We offer repairs for the 1771-ID01 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Allen Bradley - PLC and 1771-ID01?
Answer: If you buy the 1771-ID01 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the 1771-ID01 online?
Answer: Yes. Automation Stop sells the 1771-ID01 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the 1771-ID01?
Answer: The 1771-ID01 is made by Allen Bradley - PLC.
Question: What type of product is the 1771-ID01?
Answer: The 1771-ID01 is part of the PLC 5 series.
Question: What voltage is included with the 1771-ID01?
Answer: The 1771-ID01 by Allen Bradley - PLC has a voltage of 220.
For additional information about 1771-ID01 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding 1771-ID01.
Revision Part # | Also Known As | Availability |
---|---|---|
1771-ID01/A | 1771-ID01 Ser A, Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.