GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC610ACC150 |
Series: | Series One |
UPC: | 835613859796 |
Description:
This is the IC610ACC150 battery cell module. It has a battery capacity of 1800 mAH and can be found in a 2 Ampere or a 3 Ampere variant depending on the use case. This unit contains a single cell battery that has a voltage rating of 3 Volts. It has a supported temperature range of -40 degrees Celsius to +85 degrees Celsius. It is compatible with PLC modules made by GE Fanuc.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC610ACC150 is a battery module that is made by General Electric Fanuc. It has a power capacity of 1800 milliampere hours. It is available in 2 Ampere and 3 Ampere configurations and has an operating voltage of 3 Volts. This module is a one cell battery and has a battery chemistry of lithium. The height of this battery cell is 35 millimeters (1.32 inches). It has a diameter of 17 millimeters (0.68 inches). This unit is compatible with programmable logic controllers (PLCs) that belong to a variety of series and product families. It supports the modules with the part numbers IC610CPU104C IC601ACC150A, and IC610CPU101C. These are PLCs made by GE Fanuc. This battery cell is also used to power devices belonging to Series One and Series Three by the same manufacturer. It features a high energy density and has a high power capacity in a compact storage footprint. The module has a storage temperature range between -40 degrees to 85 degrees Celsius. This battery cell does not support recharging. It is contained in an enclosure that is resistant to punctures and is designed for user safety. It is built to have a high impact resistance. This battery cell contains harmful materials and should not be purposefully punctured. It should be kept away from heat and open flame. It is required to be disposed of in a safe manner after use as it is toxic to the environment if not disposed properly. This unit contains wire leads that end in connector contacts.
Question: Does Automation Stop offer repairs on the IC610ACC150?
Answer: Yes. We offer repairs for the IC610ACC150 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC610ACC150?
Answer: If you buy the IC610ACC150 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC610ACC150 online?
Answer: Yes. Automation Stop sells the IC610ACC150 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC610ACC150?
Answer: The IC610ACC150 is made by Emerson - GE Fanuc.
For additional information about IC610ACC150 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC610ACC150.
Revision Part # | Also Known As | Availability |
---|
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.