GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC610MDL125 |
Series: | Series One |
UPC: | 368705130928 |
Description:
The IC610MDL125 is a Series One digital input module that was designed and produced by Emerson - GE Fanuc. This module has a rated voltage supply of 115 volts AC, as well as a rated current of 125 amperes. This module has 8 input circuits which are divided into 2 groups of 4 circuits each. The on to off response time of this module ranges from 10 to 60 milliseconds, while the off to on response time ranges from 10 to 30 milliseconds. This device has a shipping weight of approximately 1 kilogram.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Part number IC610MDL125, which was designed and manufactured by Emerson - GE Fanuc, is a Series One digital input module. Its rated voltage supply is 115 volts AC and its rated current is 125 amperes. This module is equipped with field side circuit indicators. The input module is compact and has a shipping weight of around 1 kilogram, or 2.00 pounds, while the weight of each circuit unit is specified to be 5 ounces, or 140 grams. Additional benefits of the input module include compact construction and structure, modular design features, and the capability of mounting multiple modules.
This module is equipped with 8 input circuits designed to receive a single discrete on/off signal from user connected devices. These connected devices include push buttons, relay contacts, limit switches, and selector switches. The 8 input circuits are further divided into 2 groups of 4 circuits each. Each circuit group can work using a separate user connected power source. The specifications for each input circuit include a voltage rating of 97 to 132 volts AC at a frequency level of 47 to 63 hertz. Their input current is rated at 15 milliamperes at 60 Hz and 11.5 milliamperes at 50 hertz. The internal power consumption of the input module is rated at 10 milliamperes at 9 volts DC with the specified units of load being 1 unit at 9 volts DC. The input impedance of the circuits is specified at 9.5 kilo-ohms. The circuits are in the on-state when above 80 volts AC and in the off-state when below 20 volts AC, with the off to on response time being approximately 10 to 30 milliseconds. The on to off response time, however, is 10 to 60 milliseconds.
Question: Does Automation Stop offer repairs on the IC610MDL125?
Answer: Yes. We offer repairs for the IC610MDL125 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC610MDL125?
Answer: If you buy the IC610MDL125 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC610MDL125 online?
Answer: Yes. Automation Stop sells the IC610MDL125 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC610MDL125?
Answer: The IC610MDL125 is made by Emerson - GE Fanuc.
Question: What VAC (voltage alternating current) does the IC610MDL125 have?
Answer: The IC610MDL125 has a VAC (voltage alternating current) of 115.
For additional information about IC610MDL125 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC610MDL125.
Revision Part # | Also Known As | Availability |
---|---|---|
IC610MDL125A | IC610MDL125 Series A, Rev A | Request a Quote |
IC610MDL125B | IC610MDL125 Series B, Rev B | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.