GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC600MA507 |
Series: | Series Six |
Description:
Part number IC600MA507, which was designed and produced by Emerson - GE Fanuc, is a Lithium battery. This battery provides approximately one (1) year of data protection under no-power conditions. This battery is equipped with two (2) LED indicators. These LED indicators are labeled BATTERY and PARITY. These indicators will either be on, flashing, or be off depending on the current voltage of the battery. The normal, fully charged voltage of this battery is 2.95 volts DC at 1.00 amp-hours.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The IC600MA507 is a Lithium battery for CMOS and ASCII basic modules. This battery was produced by the company known as Emerson - GE Fanuc. This product belongs to the Series Six product line. The Series Six product line also features PLC modules and accessories. This product is compatible with the installation with 600 to 6000 CPUs. The voltage rating on this module is 3 volts, and the current rating is 1500 milliamperes. This device has physical dimensions that measure 0.48 inches x 2.38 inches x 0.48 inches. Additionally, this Lithium battery has an approximate weight of 0.12 pounds. Also, this battery for CMOS and ASCII complies with and tops the GE Fanuc PLC standards and specifications. This Lithium battery provides approximately one (1) year of data protection when under no-power conditions.
Part number IC600MA507 is equipped with a total of two (2) LEDs, or light emitting diodes. These LEDs provide indicators for different aspects of this Lithium battery. One (1) of the two (2) LEDs indicate the condition of the IC600MA507 Lithium battery. This LED is labeled as BATTERY. This LED will light up when power is applied to the CPU, as long as the battery condition is normal. The normal, fully charged voltage of this Lithium battery is 2.95 volts DC at 1.00 amp-hours. This LED indicator with flash if the voltage of the battery is low. This voltage range is 2.55 volts to 2.75 volts. If the voltage of the battery drops below 2.55 volts, the BATTERY LED will turn off. The remaining LED indicator of this Lithium battery is labeled PARITY.
Question: Does Automation Stop offer repairs on the IC600MA507?
Answer: Yes. We offer repairs for the IC600MA507 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC600MA507?
Answer: If you buy the IC600MA507 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC600MA507 online?
Answer: Yes. Automation Stop sells the IC600MA507 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC600MA507?
Answer: The IC600MA507 is made by Emerson - GE Fanuc.
For additional information about IC600MA507 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC600MA507.
Revision Part # | Also Known As | Availability |
---|
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.