GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | ST-4424 |
Series: | RSTi PacSystem |
UPC: | 799705804920 |
Description:
The ST-4424 output module includes a simple push spring clamp termination that requires no additional wiring tools. This device comes with a push spring clamp termination, so there are no additional tools required for wiring.This is a CE and UL approved device and it is ideally suited and compatible with GE Fanuc's products and modules that are PACSystems RSTi. Additionally, they're all part of a distributed system with efficient functionality that may be input or output, allowing operators to achieve a low-cost installation with a high uptime.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The ST-4424 analogue output module has four output channels, along with voltage that ranges from zero (0) to ten (10) volts direct current (DC) and the channel has a twelve (12)-bit resolution. This CE and UL listed device is well suited and compatible with GE Fanuc's products and modules that are PACSystems RSTi. They are all members of an efficient functionality distributed system which is input or output, aiding operators to get an affordable installation along with a high uptime. The ST-4424 output module has a simple push spring clamp termination and does not require any additional wiring tools. This module also comes with a push spring clamp termination. There is no need for any additional tools needed for wiring. Like most other modules, this module has an operating temperature that must be maintained, and it ranges from zero (0) to fifty (50) degrees Celsius. When storing this device, the temperature of the area must be kept between negative forty (-40) and eighty-five (85) degrees Celsius. Additionally, the surrounding area of the module and where it has been mounted should also contain the relative humidity ranging from five (5) to ninety (90) percent. The shock ratings of this device, both operational and non-operational, is ten (10) G and thirty (30) G, respectively. The output for channel zero (0) is pin zero (0) on the module, along with the output for Channel one (1) being pin one (1). The output for channel two (2) is pin two (2). The same can be said for channel three (3).
Question: Does Automation Stop offer repairs on the ST-4424?
Answer: Yes. We offer repairs for the ST-4424 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and ST-4424?
Answer: If you buy the ST-4424 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the ST-4424 online?
Answer: Yes. Automation Stop sells the ST-4424 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the ST-4424?
Answer: The ST-4424 is made by Emerson - GE Fanuc.
For additional information about ST-4424 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding ST-4424.
Revision Part # | Also Known As | Availability |
---|
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.