GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Emerson - GE Fanuc |
Product Type: | Automation Product |
Part Number: | IC695ALG728 |
Series: | RX3i PacSystem |
UPC: | 6490420533 |
Description:
The GE Fanuc Emerson IC695ALG728 is an analog voltage/current output module that can be employed for Rx3i PACSystems. The device supports the HART 5.0 communication protocol. This module provides eight non-isolated output channels. These outputs can be programmed for either current or voltage output ranges. The IC695ALG728 weighs approximately 230 grams (0.5 pounds) while shipping.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The GE Fanuc Emerson IC695ALG728 is an analog voltage/current output module that can be employed for Rx3i PACSystems. The device supports the HART 5.0 communication protocol. This module provides eight non-isolated output channels that can be enabled or disabled individually with two HART modems that provide an update rate of 2 seconds. The device offers a fast channel acquisition time of 16 milliseconds. The outputs can be programmed for either voltage or current output ranges: from 4 milliamperes to 20 milliamperes with a resolution of 15.6 bits, from 0 milliamperes to 20 milliamperes with a resolution of 15.9 bits, from 0 volts DC to 10 volts DC with a resolution of 14.9 bits or from -10 volts DC to 10 volts DC with a resolution of 15.9 bits. This module draws a current of 340 milliamperes at a voltage of 3.3 volts DC.
The IC695ALG728 supports either 32 bit or 16-bit integer data output that can be set as floating-point IEEE. The device has a red/green LED indicator labeled “TB” that indicates the state of the terminal block. The module supports a spring, box, extended spring, or extended box style front terminal block. The output module can be easily mounted in an RX3i universal backplane. The IC695ALG728 has three LED indicators that are located on the faceplate to show the power and field status of this module. This module provides diagnostics features and offers the possibility to the user to employ an external isolated power supply with a voltage of 24 volts DC. The IC695ALG728 weighs approximately 230 grams (0.5 pounds) while shipping and operates at 0 degrees to 60 degrees Celsius (32 degrees to 140 degrees Fahrenheit) for industrial applications.
Brand | GE Automation Fanuc / Emerson Automation |
Series | PACSystems RX3i |
Part Number | IC695ALG728 |
Description | Non-isolated voltage/current analogue output module with HART communications |
Number of channels | 8 |
Load requirement | 340 mA at +3.3VDC, 190 mA at +24VDC Isolated |
Isolation, Field to Backplane | 2550VDC for one second |
Output settling time | Voltage / current output: 2 ms/70 ms, 0 to 95% |
Output current ranges | 0 to 20mA, 4 to 20mA |
Output voltage ranges | +/- 10V, 0 to 10V |
Power dissipation within module | 7.25 Watts maximum |
External power supply | Voltage Range: 19.2V to 30V (24V nominal) / Current: 190 mA maximum |
Resolution | +/-10V: 15.9 bits, 0 to 10V: 14.9 bits, 0 to 20mA: 15.9 bits, 4 to 20mA : 15.6 bits |
Analog update rate | 16 milliseconds |
Output overvoltage protection | Current outputs only: -30V for 60 seconds, +30V for one hour |
Maximum output load | Current: 850 Ohms maximum / Voltage: 2 Kohms minimum |
HART communications | Version 5.0 |
Weight | 230 g (0.5 lb.) |
Question: Does Automation Stop offer repairs on the IC695ALG728?
Answer: Yes. We offer repairs for the IC695ALG728 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC695ALG728?
Answer: If you buy the IC695ALG728 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC695ALG728 online?
Answer: Yes. Automation Stop sells the IC695ALG728 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC695ALG728?
Answer: The IC695ALG728 is made by Emerson - GE Fanuc.
Question: What Analog update rate does the Rockwell-Automation IC695ALG728 have?
Answer: The Rockwell-Automation IC695ALG728 has a Analog update rate of 16 milliseconds.
Question: What Brand does the Rockwell-Automation IC695ALG728 have?
Answer: The IC695ALG728 has a GE Automation Fanuc / Emerson Automation Brand.
Question: Does the Allen-Bradley IC695ALG728 have a Description?
Answer: Non-isolated voltage/current analogue output module with HART communications.
Question: What is the External power supply component of the IC695ALG728?
Answer: The Rockwell Automation IC695ALG728 has a External power supply of Voltage Range: 19.2 volts to 2 volts (2 volts nominal) / Current: 190 mA maximum.
Question: What HART communications does the Rockwell Automation IC695ALG728 have?
Answer: The HART communications of the IC695ALG728 is Version 5.0.
Question: What is the Isolation, Field to Backplane of the Rockwell-Automation IC695ALG728?
Answer: The Isolation, Field to Backplane of the Rockwell-Automation IC695ALG728 is 2550VDC for one second.
Question: What is the Load requirement of the Allen Bradley IC695ALG728?
Answer: The IC695ALG728 has a Load requirement of 340 mA at +3.3VDC, 190 mA at +24VDC Isolated.
Question: What is the Maximum output load of the IC695ALG728?
Answer: The IC695ALG728 has a Maximum output load of Current: 850 Ohms maximum / Voltage: 2 Kohms minimum.
Question: What is the Number of channels of the IC695ALG728?
Answer: The Number of channels of the Rockwell-Automation IC695ALG728 is 8.
Question: What Output current ranges does the IC695ALG728 have?
Answer: The Allen Bradley-Rockwell Automation IC695ALG728 has a Output current ranges of 0 to 20mA, 4 to 20mA.
Question: What is the Output overvoltage protection of the IC695ALG728?
Answer: The Output overvoltage protection of the IC695ALG728 is Current outputs only: -30 volts for 60 seconds, +30 volts for one hour.
Question: What is the Output settling time of the Allen-Bradley IC695ALG728?
Answer: The IC695ALG728 has a Output settling time of Voltage / current output: 2 ms/70 ms, 0 to 95%.
Question: What Output voltage ranges does the Rockwell Automation IC695ALG728 have?
Answer: The Rockwell Automation IC695ALG728 has a Output voltage ranges of +/- 10 volts 0 to 10V.
Question: What is the component Number of the IC695ALG728?
Answer: The Rockwell-Automation IC695ALG728 has a unit Number of IC695ALG728.
Question: What is the Power dissipation within module of the Allen-Bradley IC695ALG728?
Answer: The Power dissipation within module of the Allen-Bradley IC695ALG728 is 7.25 Watts maximum.
Question: What is the Resolution of the IC695ALG728?
Answer: The Resolution of the Allen Bradley IC695ALG728 is +/-10 volts 15.9 bits, 0 to 10 volts 14.9 bits, 0 to 20mA: 15.9 bits, 4 to 20mA : 15.6 bits.
Question: What Weight does the Allen Bradley-Rockwell Automation IC695ALG728 have?
Answer: The IC695ALG728 has a Weight of 230 g (0.5 lb.).
For additional information about IC695ALG728 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC695ALG728.
Revision Part # | Also Known As | Availability |
---|---|---|
IC695ALG728-AA | IC695ALG728 Series AA, Rev AA | Request a Quote |
IC695ALG728-AB | IC695ALG728 Series AB, Rev AB | Request a Quote |
IC695ALG728-BB | IC695ALG728 Series BB, Rev BB | Request a Quote |
IC695ALG728-CB | IC695ALG728 Series CB, Rev CB | Request a Quote |
IC695ALG728-DC | IC695ALG728 Series DC, Rev DC | Request a Quote |
IC695ALG728-EC | IC695ALG728 Series EC, Rev EC | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.