GE / IP FANUC Series 90/30 In Stock
| Manufacturer: | Emerson - GE Fanuc |
| Product Type: | Automation Product |
| Part Number: | IC697MDL251 |
| Series: | Series 90-70 |
| UPC: | 974988978173 |
Description:
GE Fanuc produces the IC697MDL251 input module, which is part of the Series 90-70. This input module contains 16 points divided into four groups, each with four input points. The 16-point containing module accepts a variety of input devices, including limit and selection switches, two- and three-wire proximity switches as well as pushbuttons switches. There is a need for 0.35 amps through the backplane's 5-volt bus.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
Pay
We accept credit cards from all major providers, as well as PayPal.
Ship
We offer worldwide shipping with UPS and DHL.
Warranty
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
IC697MDL251 module is an input module from the Series 90-70 product range from GE Fanuc. The 16 input points of the IC697MDL251 Input Module are divided into four groups, each with four points. Because each group is separated, it is compatible with and may be utilized with a separate AC voltage supply phase. The mechanical tuning of the IC697MDL251 Module allows for easy field substitution with a similar kind of module. Limit and selection switches, push buttons, and electric proximity switches with two and three wires are all compatible with this 16-point input module. Through the 5 Volts bus on the device's backplane, a current of 0.35 amps is required.
The mechanical key on the GE Fanuc IC697MDL251 Input Module is devoted to preventing any inadvertent or illegal switching of modules in a given slot. When users desire to alter the Module's placement after the key latching procedure, the Module allows the key to be withdrawn by pushing it upwards, and it unhooks as it comes off the rail. The Module and key can then be reinserted when the installation site has been confirmed. Each of the four input groups requires a connection from the power source to the input terminal in the wiring of the IC697MDL251 Module. Wire sizes 14 to 22 can be used on the detachable field-wiring terminal board. A cable tie that runs through the cleat in the board's lowest corner secures the bundle of wires on the terminal board. Make sure the main power supply is turned off before removing the board.
FAQ
Question: Does Automation Stop offer repairs on the IC697MDL251?
Answer: Yes. We offer repairs for the IC697MDL251 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Emerson - GE Fanuc and IC697MDL251?
Answer: If you buy the IC697MDL251 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the IC697MDL251 online?
Answer: Yes. Automation Stop sells the IC697MDL251 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the IC697MDL251?
Answer: The IC697MDL251 is made by Emerson - GE Fanuc.
Series information for IC697MDL251
For additional information about IC697MDL251 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding IC697MDL251.
| Revision Part # | Also Known As | Availability |
|---|---|---|
| IC697MDL251D | IC697MDL251 Series D, Rev D | Request a Quote |
| IC697MDL251E | IC697MDL251 Series E, Rev E | Request a Quote |
| IC697MDL251H | IC697MDL251 Series H, Rev H | Request a Quote |
Common Misspellings:
- IC697MDL25I
- IC697MDL2S1
- IC697MDL2SI
- ICG97MDL251
- ICG97MDL25I
- ICG97MDL2S1
- ICG97MDL2SI
- 1C697MDL251
- 1C697MDL25I
- 1C697MDL2S1
- 1C697MDL2SI
- 1CG97MDL251
- 1CG97MDL25I
- 1CG97MDL2S1
- 1CG97MDL2SI
