The Allen-Bradley 22A-D2P3N104 PowerFlex 4 adjustable frequency AC drive provides a full-featured 4 digits alphanumeric human interface liquid crystal (LCD) display module to show either parameter number and value, or fault code with an integral keypad to program and control using the local potentiometer both torque and speed of three-phase induction motors in industrial applications. This Allen-Bradley PowerFlex 4 adjustable frequency AC drive includes an internal dynamic IGBT brake that saves efficiently switching regenerative energy without adding external chopper circuits. The Allen-Bradley 22A-D2P3N104 can be mounted with an input circuit breaker or fuses. This Allen-Bradley adjustable frequency AC drive produces torque efficiently over a large speed range and offers sensorless vector control. The Allen-Bradley 22A-D2P3N104 AC drive supports shielded and unshielded cables for wiring and installation. The Allen-Bradley 22A-D2P3N104 provides removable MOV to ground ungrounded distribution systems to increase motor life. The Allen-Bradley 22A-D2P3N104 provides an efficient integral electromagnetic compatibility (EMC) filtering and external filters to meet EMC needs. The Allen-Bradley 22A-D2P3N104 PowerFlex 4 adjustable frequency AC drive includes relay pre-charge to limit inrush current.

This Allen-Bradley 22A-D2P3N104 PowerFlex 4 drive contains 10 LED indicators that report and display visual notification of drive status and information. The Allen-Bradley 22A-D2P3N104 AC drive supports an input voltage rating of 480 volts AC and current consumption of 2.3 amperes with a maximum power rating of 1 horsepower and 0.75 kilowatts. This Allen-Bradley 22A-D2P3N104 supports the RS485 (DSI) protocol to communicate with Rockwell Automation devices and to program from a PC. The 22A-D2P3N104 AC drive is constructed to meet the IP20 and NEMA Type open enclosure ratings. The Allen-Bradley 22A-D2P3N104 can be installed vertically on 35 millimeters DIN on A frame drives or using M4 screws. The Allen-Bradley 22A-D2P3N104 offer an adjustable pulse width modulation (PWM) frequency up to 16 kHz to ensure proper operation. This adjustable frequency AC drive can operate at a temperature range of 10 degrees to 50 degrees Celsius (14 degrees to 122 degrees Fahrenheit) for industrial applications from fans to extruders and weighs approximately 1.4 kilograms (3.1 pounds) while shipping.

The Allen-Bradley 22A-D2P3N104 is a variable frequency drive (VFD) used for AC motor control, or in other words, to control motor speed and delivered torque. It uses high voltage at an input range of 342 - 528 volts AC with 3 phases and it provides high voltage at output at a range of 0 - 480 volts AC with 3 phases with a continuous output current of 2.3 amperes. This drive is vector controlled device and it uses sensor-less technique. Thanks to that method, it is possible to achieve very good and linear speed up characteristics, overcome the load torque as required and have both speed and torque control. Due to that, this VFD is excellent for pump control applications where others, standard VFD’s easily lose control. Configuration at the start and other parameters can be set up locally or remotely. At VFD front side there are supplied fixed digital keypad and LED display. Using them, it is possible to JOG or RUN the drive locally and to setup internal drive parameters. That parameters will locate the drive close to the application requirements that has to be achieved, but without any fault during the long period of time. The drive has its many (analog and digital) control lines with several preset capabilities and also many defaults can be used. For the communication purposes, network access but also for programming, the RS485 port is provided, and there existing an option to convert it to RS-232 interface if needed so. The drive is under IP20 protection and its normal operation should not be done outside of an ambient temperature ranging from 14 to 122 degrees Fahrenheit.