GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Allen Bradley - Motors |
Product Type: | Drive |
Part Number: | 1326-CPB1-015 |
Series: | 1326 |
Description:
The 1326-CPB1-015 is an Allen Bradley power cable belonging to the series B of 1326 cables used for AC servo motors of four hundred and sixty (460) volts. It has a total cable length of fifteen (15) meters and a minimum bend radius of seventy-six point two (76.2) millimeters. The maximum diameter of this product's cable measure out to fourteen (14) millimeters. The connector height of this product measures out to one hundred and ten (110) millimeters.
Key Features:
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The 1326-CPB1-015 is an Allen Bradley power cable belonging to the series B of 1326 cables used for AC servo motors of four hundred and sixty (460) volts. It has a total cable length of fifteen (15) meters and a minimum bend radius of 76.2 millimeters. The cables are built with a braided cable shield to provide protection from electromagnetic noise. For easy maintenance and installation, the Allen Bradley 1326-CPB1-015 has molded pull/push connectors that are attached to the side of the motor. The cable shows a good rating for the minimum bend radius and a good flex cycle of life. The 1326-CPB1-015 is a standard power cable for 1326AS-B4xxx and 1326AS-B3xxx Allen-Bradley products. The cable has a bend radius of seventy-six point two (76.2) mm, as well as a connector height one hundred and ten (110) millimeters. The maximum diameter of the Allen Bradley 1326-CPB1-015's cable is fourteen (14) mm. With the L option, The Allen Bradley 1326-CPB1-015 is 47 and without the L option, it is 43.2. The cable has nine (9) wires, with the first three (3) being for power. These wires are black in color and are 1.29 mm² gauge. The fourth (4th) and sixth (6th) wires are for the brake and are also the color black. The 5th and 9th wires on the Allen Bradley 1326-CPB1-015 are for the thermostat and are black in color as well. The 7th and 8th wires are for ground. One of these wires is black, while the other is a drain wire.
Question: Does Automation Stop offer repairs on the 1326-CPB1-015?
Answer: Yes. We offer repairs for the 1326-CPB1-015 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Allen Bradley - Motors and 1326-CPB1-015?
Answer: If you buy the 1326-CPB1-015 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the 1326-CPB1-015 online?
Answer: Yes. Automation Stop sells the 1326-CPB1-015 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the 1326-CPB1-015?
Answer: The 1326-CPB1-015 is made by Allen Bradley - Motors.
For additional information about 1326-CPB1-015 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding 1326-CPB1-015.
Revision Part # | Also Known As | Availability |
---|---|---|
1326-CPB1-015/A | 1326-CPB1-015 Ser A, Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.