GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Allen Bradley - Miscellaneous |
Product Type: | PLC/Programmable Logic Controller |
Part Number: | 1734SC-IE4CH |
Series: | Point I/O 1734 |
Description:
Part number 1734sc-IE4CH is a Point I/O module with a single end, 4- to 20-milliampere current sensor input module. The voltage drop through an integrated resistor can be used to measure analog current. Moreover, each channel's standard input resistance is 250 ohms. At 24 volts DC, the backplane on this controller can draw current at 20 mA. One (1.0) watt is the thermal dissipation rate for this controller. This device has 16-bit resolution.
Key Features:
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The 1734SC-IE4CH is a Point I/O module that was designed and manufactured by Spectrum Controls. This module has 4 different I/O channels. This module has a 16-bit resolution. It supports input via the Analog+ HART protocol. 250 ohms is the input impedance rating for this controller. It comes with over current protection of 28 mA. The thermal dissipation rating on this controller is 1 watt. This controller allows HART data acquisition and standard analog acquisition. It helps with simplifying the commissioning and maintenance of the connected HART device.
The 1734SC-IE4CH can be deployed as a HART master. It can be deployed to form communication with other HART field units. There are multiple LED lights on the front mount of this unit. These LEDs have the primary responsibility of displaying the operation status, the module status, network status, as well as the channel status. This controller supports multiple of communication protocols such as the DeviceNet, Ethernet adapter, and the ControlNet.
Each channel of this module can independently program the HART protocol. The 1734SC-IE4CH is the primary HART master module. Additionally, the connected field device is the HART slave device. The Spectrum Controls 1734sc-IE4CH Point I/O module has an operating temperature range of-20 to 55 degrees Celsius, or -4 to 131 degrees Fahrenheit. The non-operating temperature range of this device, however, is -40 to 85 degrees Celsius, or -40 to 185 degrees Fahrenheit. The relative humidity of the device's surrounding area should remain within a range of 80 to 95 percent condensing when operational.
Question: Does Automation Stop offer repairs on the 1734SC-IE4CH?
Answer: Yes. We offer repairs for the 1734SC-IE4CH and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Allen Bradley - Miscellaneous and 1734SC-IE4CH?
Answer: If you buy the 1734SC-IE4CH through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the 1734SC-IE4CH online?
Answer: Yes. Automation Stop sells the 1734SC-IE4CH online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the 1734SC-IE4CH?
Answer: The 1734SC-IE4CH is made by Allen Bradley - Miscellaneous.
Question: What type of product is the 1734SC-IE4CH?
Answer: The 1734SC-IE4CH is part of the Point I/O 1734 series.
For additional information about 1734SC-IE4CH check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding 1734SC-IE4CH.
Revision Part # | Also Known As | Availability |
---|---|---|
1734SC-IE4CH/A | 1734SC-IE4CH Ser A, Series A, Rev A | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.