GE / IP FANUC Series 90/30 In Stock
Manufacturer: | Horner Electric |
Product Type: | Automation Product |
Part Number: | HE693THM406 |
Series: | PLC I/O |
UPC: | 799705796126 |
Description:
The Horner Electric APG HE693THM406 is an input thermocouple module with four channels and no alarms. The resolution of module is 5�C. The total power consumption of this device is 100 mA current at a voltage of 5 volts DC. An input impedance is more than 20 mega-ohms with a +/- 12 volts common mode range. The analog to digital conversion is integrating with a 45 channel per second update rate.
Automation Stop is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with Automation Stop's 1-year warranty.
We accept credit cards from all major providers, as well as PayPal.
We offer worldwide shipping with UPS and DHL.
We proudly offer a one year Automation Stop warranty on most products.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
The Horner Electric Advance Products Group HE693THM406 Thermocouple Input Module allows the temperature sensors of the thermocouple to be directly in contact with a PLC without any signal processors, such as transducers, transmitters, and much more. All the thermocouple signal processing of digital and analog signals is performed on the same module. The input range of this thermocouple module depends on the temperature that is supported. The supported ranges include: -210 to +1000 degrees Celsius for Type J, -270 to +1372 degrees Celsius for Type K, 0 to +1768 degrees Celsius for Type R, -270 to +1300 degrees Celsius for Type N, 0 to +1768 degrees Celsius for Type S, and -270 to +400 degrees Celsius for Type T.
This module has a 0.5°C resolution, therefore the I/O of the PLC is reported in fragments of 0.5°C difference. The accuracy is typically +/- 0.5°C in type J. This model for the thermocouple has four (4) input channels and the power consumption is 100 milliamperes at 5 volts DC. The input / output points require a 4%AI [&16%I] with an input impedance being greater than 20 mega-ohms. This module has a maximum safe overload of +/- 35 volts and the common mode range is +/- 12 volts. The integrating analog to digital conversion has a module update rate of 45 channels per second. The operating temperature for this device should remain within a range of 0 to 60 degrees Celsius, or the equivalent range of 32 to 140 degrees Fahrenheit. The relative humidity for this device should be 5% to 95% non-condensing.
Question: Does Automation Stop offer repairs on the HE693THM406?
Answer: Yes. We offer repairs for the HE693THM406 and it comes with our 1 Year Automation Stop Warranty.
Question: What type of warranty comes with the Horner Electric and HE693THM406?
Answer: If you buy the HE693THM406 through Automationstop.com it comes with our 1 Year Warranty and no other warranties.
Question: Can I buy the HE693THM406 online?
Answer: Yes. Automation Stop sells the HE693THM406 online and you can check out for the quantity and condition listed available above.
Question: What is the manufacturer for the HE693THM406?
Answer: The HE693THM406 is made by Horner Electric.
For additional information about HE693THM406 check the data sheet or manual. Also check the manual PDF for all wiring diagrams, compatibility, troubleshooting, specifications, installation instructions, and accessories (such as batteries, terminal blocks, or cables) regarding HE693THM406.
Revision Part # | Also Known As | Availability |
---|---|---|
HE693THM406C | HE693THM406 Series C, Rev C | Request a Quote |
HE693THM406D | HE693THM406 Series D, Rev D | Request a Quote |
Common Misspellings:
Automation Stop sells used surplus products. Automation Stop is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by Automation Stop come with Automation Stop’s 1-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.
Rockwell Disclaimer: The product is used surplus. Automation Stop is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Automation Stop is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Automation Stop also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Automation Stop also makes no representations as to your right to install any such firmware on the product. Automation Stop will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.